-
Gypsum Stucco Lightweight finishing mortar, based on gypsum, for interior stucco on walls and ceilings, with guaranteed durability. Formulated with additives that improve adhesion on a wide variety of substrates, improve water retention, improve mix consistency and stability, and confer repellency and hydrophobicity. Use and application Stucco for interior plastering of walls and ceilings, for application in a thin layer (0.1-3.0) mm. It complies with the performance certificate B4 and C7 in accordance with the provisions of the UNE-EN 13297-1 Standard. Presentation: Sacks of 13 Kg Colors: White. Data sheet: Download -
High strength and flexibility adhesive. C2T type adhesive according to ISO 13007-1 standard. Used in highly demanding systems. Its formulation based on Portland cement, selected aggregates, organic additives and resins that improve its workability and adherence to mortar-glue. Scope In the placement of non-absorbent materials in general, such as porcelain stoneware and glass mosaic, indoors and outdoors. In pavements with intense traffic, it provides great flexibility and adherence, as well as high resistance to compression and shear to be able to withstand the loads and efforts caused by the circulation of intense traffic. In facade cladding, thanks to its flexibility, it is able to withstand thermal shocks and the small differential movements produced by the support. Its high adherence makes it possible and very good to place it on old substrates. Presentation: Sacks of 22.7 Kg Colors: Gray. Data sheet: Download -
Special adhesive with high adhesion and flexibility Adhesive Type C2TES1 according to ISO 13007-1 Euroflex is an adhesive designed for use in a highly demanding system. It is used for the placement of low absorption materials in general such as porcelain tiles, natural stones, etc. It is recommended for pavements with intense traffic, since Euroflex provides great flexibility and adherence, as well as to withstand large loads and efforts. Presentation: 20 Kg bags Colors: White. Data sheet: Download -
Melt for floors It is an additive mortar based on cement, mineral pigments in color, aggregates of controlled fine granulometry, synthetic resins in dispersion and organic and inorganic additives. Pigments are resistant to light, water and the basic cement medium. It comes in a wide range of colors to satisfy any requirement, allowing you to create many combinations with the tone and decoration of any ceramic tile. Its greatest quality is that of hardening in a short time, avoiding the formation of cracks and fissures due to its high degree of flexibility, as well as its waterproofing power. It also prevents the appearance of micro-organisms. Scope Ideal for grouting ceramic floors and wall tiles in general up to 5 mm wide between both interior and exterior pieces. In ceramics with microporosities, carry out a test to verify the subsequent cleaning or consult the technical department. Presentation: Sacks of 5 Kg Colors: According to the color chart. Data sheet: Download -
Mix pañete M10 class masonry mortar for interior and exterior wall finishes. Composed of Portland type cement, selected aggregates and additives. Designed with technically controlled proportions that give it adhesion, cohesiveness, fluidity and texture properties in a fresh state, as well as durability, good appearance and mechanical resistance in a hardened state. Use and Application: This mortar is recommended to be applied to the finishes or finishes of the walls, masonry, concrete, bricks or encaches, both indoors and outdoors. To obtain the desired workability, it is necessary to knead in a mortar mixer. For small quantities or leagues, they can be mixed manually. Presentation: 42.5 Kg sacks Appearance: Gray powder of medium granulometry. Data sheet: Download -
Fine pañete mix Fine-grained masonry mortar (less than 0.6 mm), for interior wall finishes. Composed of Portland type cement, selected aggregates and additives. Designed with technically controlled proportions that give it adhesion, cohesiveness, fluidity and texture properties in a fresh state, as well as durability, good appearance and mechanical resistance in hardened states. Also available with waterproof properties. This mortar is recommended to be applied indoors on walls, masonry, concrete, brick or mortar. To obtain the desired workability, it is necessary to knead in a mortar mixer. For small quantities or leagues, they can be mixed manually. Presentation: 42.5 Kg bags Colors: Gray Technical Data: Download -
Rustic pañete mix Rustic granulometry masonry mortar (up to 2.36 mm), for interior or exterior wall finishes for structural or high-resistance use. Composed of Portland type cement, selected aggregates and additives. Designed with technically controlled proportions that give it adhesion, cohesiveness, fluidity and texture properties in a fresh state, as well as durability, good appearance and mechanical resistance in a hardened state. Use and application This mortar is recommended to be applied indoors or outdoors, on walls, masonry, concrete, brick or mortar. The size of its aggregates only allows to obtain rough finishes. To obtain the desired workability, it is necessary to knead in a mortar mixer. For small quantities or leagues, they can be mixed manually. Presentation: 42.5 Kg sacks Appearance: Gray powder of medium granulometry. Data sheet: Download -
Plaster Mix Pre-mixed dry mortar for plastering panels (polystyrene or foam) with indoor or outdoor application. Composed of type I Portland cement, selected aggregates and additives that give it controlled adhesion, cohesiveness, fluidity and texture properties in the fresh state, as well as mechanical resistance and excellent appearance in the hardened state. Use and Application Mortar recommended for the correction of modular panels (expanded polystyrene type) or divisions reinforced by steel mesh, both in interior installations (load-bearing or non-load-bearing) and outside (facades with load-bearing or non-load-bearing characteristics). To obtain the desired workability, it is recommended to knead in a mortar mixer. For small quantities or leagues, they can be mixed manually within a wheelbarrow or other controlled surface to avoid contamination with external agents or disproportion of the mixture. Presentation: Sacks of 42.5 Kg Colors: Gray SPECIAL MORTARS Technical Sheet: Download -
Adhesive mixture for fixing ceramics and stoneware, for interior and exterior use. Formulated from hydraulic binders with a white or gray base, aggregates of balanced granulometry and additives that give it properties of adherence, water retention, fluidity and controlled workability. Use and Application Used for laying ceramic tiles with high water absorption (absorption 7-25%). Recommended for conditions with minimal requirements, such as interior walls, low traffic floors, etc. Recommended for laying ceramic tiles, stoneware, porcelain tiles and mosaics on mortar, concrete or concrete surfaces. It is recommended to knead manually or mechanically in small quantities of the product for better homogeneity. It is recommended to use a notched trowel as a tool for the application of this product, which will allow a better adhesion between the substrate and the mixture. Presentation: Sacks of 22.7 Kg Colors: Gray. Data sheet: Download -
Pegacol - Adhesive for ceramic and stoneware. Type C1T Adhesive According to ISO 13007-1 Ceramic adhesive composed of Portland cement, organic and inorganic additives, aggregates of selected granulometry and synthetic resins that improve workability, water retention and adhesive mortar adhesion. Fields of application Designed to be used for laying high and medium absorption ceramic floor and wall tiles on substrates covered with mortar, concrete, mosaic, and artificial stone. Its use or employment is recommended for interiors. Presentation: Sacks of 22.7 Kg Colors: Gray. Data sheet: Download -
High adhesion white adhesive Type C1T Adhesive according to ISO 13007-1 This is a white adhesive with high adhesion power, formulated based on white cement, selected aggregates with controlled granulometry, organic additives and resins that improve workability, retention of water and adhesion of the mortar-glue. Fields of application It is also recommended for coating mortar renderings, due to its high adherence it provides a good fixation of the pieces. For the placement of white or translucent (high and medium absorption) ceramic pavements and wall tiles indoors and outdoors and for the placement of ceramic pieces on old mosaic and terrazzo floors. Presentation: Sacks of 22.7 Kg Colors: White. Data sheet: Download -
Adhesive for porcelain and stoneware Adhesive Type C2 according to ISO 13007-1 standard Pegacol Porcelánico is an adhesive designed for laying ceramic and porcelain floor and wall tiles on mortar, concrete, mosaic, artificial stone substrates indoors and outdoors. It offers high fixing power and easy application. Presentation: 22.7 Kg bags Colors: Grey. Data sheet: TO DOWNLOAD
